Installing Wire Insert on Multiple Layers of Plastic

In response to a few questions about increased difficulty of installing the wire insert on 3 layers of 7.2 mil plastic. I have done my experiment with zero added degree of difficulty.

I don’t want to leave it just like that. I would like to add a few points.

First of all, the temperature was about 18C when I did this. It will progressively get more difficult because the plastic is less pliable as the temperature gets colder.

I should follow this up with the same experiment when the temperature is below freezing.

For my experiment I put extra screws into the channel simply to increase the chances of interference between wire insert and screws.

I had one instance where it was a little more tricky and had to push a little harder.

I could see that there could be a possibility where you might need to take out the wire insert and start 1 centimeter over.

There are a few things which I wish to point out on logistics and technique. There is a critical thing to remember for the helper who is pulling on the loose plastic.

He/she must be pulling at least 30 cm ahead of where the wire is going into the channel to allow the necessary slack to get the wire into the channel.

The same applies for the person inside the structure who is pulling on the end wall cover.

Inserting the wire insert is very much a wrist action and proper technique is probably even more important when doing 3 layers of 7.2 mil

Your thumb should be on the next equal bump (either up or down) so that you can apply some twisting action to the insert.

Never simply slide the insert up and down as this can abraid the cover.

I hope this helps

Norm

Installing Multi Shelter Solutions Buildings

One of the most common questions we get asked is regarding installation of our structures. We have tried to create a simple yet effective solution for your applications, and recently have revamped our installation guide with more pictures, a glossary and more detailed instructions about everything to empower our customer more.

These structures are supplied as kits, intended for our customer to be able to install themselves. We are available for whatever questions you may have. We have confidence that you will be able to install these structures yourselves with a small team of people. You will get a complete manual with every order. You can download our instruction manual through the links below for a preview or to prepare for your delivery.

There is quite a bit of information contained in this manual that it CRITICAL to be understood. These structures are more complex to assemble than your typical Swedish Furniture.

The pages are in the order they should be read.
#1-2 are very important notes about installation and the rest of the manual.
1. START HERE
2. Warranty, Codes & Site Requirements
3. Anchoring-Base Brackets
3. Anchoring-Anchor Posts
4. ridge & hoops
5. Purlins & Windbraces
6. -optional- Cross Ties
7. Covering-Plastic Roof
7. Covering-Tarp Roof
8. -optional- Roll up Side Walls
9. Wirelock & Side Wall Cover Fasteners
10. -optional- Inflator Fan
11. Ends
12. -optional- Door Options

click here to download a step by step breakdown of the process in PDF format and click here to see a photo explanation of the process. You can also view the additional articles, links or videos on our how to page. Please note, not all pages or options apply to everyone. TO BE USED IN CONJUNCTION WITH THE MANUAL ABOVE, NOT AS A STAND ALONE RESOURCE.

Please see our more detailed installation page for more information

Cold Weather Poly Install

If you were one of the many people who, last fall, were faced with putting the cover on in less than ideal weather, you will be looking at significant wrinkles once the weather starts to warm up.

You will need to tighten the cover to prevent premature wear due to flapping in the wind.

Tightening does not have to be done all at once. You can do half one day and half on another.

It is important to remember that you are always pulling at 90 degrees to the wrinkles. Most of the tightening will need to be done lengthwise first.

If you have a loose cover and no time this week to tighten things,
there is a temporary fix!

  • Take a soft length of rope (do not use nylon!) and throw it over the building where the cover is particularly loose.
  • Tie the rope off at the base as tight as you can.

Please call if you need clarification for this procedure and we would be happy to help