Tag Archives: loose building plastic

Retightening a Loose Structure Cover

Previously we outlined how to do a temporary fix for loose cover. This should not be left for an extended period. Re-tightening a cover does not have to be done in one day.

  • The job MUST split into two parts lengthwise.
  • The cover must be pulled lengthwise BEFORE it is pulled from side to side.
  • Make sure you do the tightening process on a calm, warm day.
  • You should do the end which looks the worst first.
  • This job will require taking ALL of the cover fasteners out.

Taking a short cut will leave you with more wrinkles.
Areas with wrinkles will flutter more and cause stress points.
This will also cause the cover to deteriorate quicker.

When you are tightening the cover, you should always pull 90 degrees to the wrinkle.

This means that after you have secured at the peak,
most often you will be pulling diagonally to the corner.

Once you have done one end/half and the wind is still down, you can start loosing the fasteners on the other end and repeat the process until complete.

Please don’t hesitate to contact us if you have any questions.

You can also see additional information in our installation guide:
Tarp Covering Instructions
Plastic Covering Instructions
Wirelock & Side Wall Cover Fasteners
covering options

Temporary Fix for a Loose Cover

There are a number of instances where a cover will need to be installed in less than ideal conditions. This can be either be on a windy day or in the cold (-10C or worse) and the job simply can not wait.

This will almost invariably lead to a situation where the cover will need to be re-tightened on a warmer and/or calmer day.

Doing this temporary fix will get you an extra month of time that you can wait until it warms up and you can do a better job retightening the loose cover.

The lifespan of a cover can very quickly be reduced if it is repeatedly flapping in the hard wind. A very effective, temporary fix to give you more time to do the job right, is to put ropes or straps over the building (as in the photos below)

A 1” or 2” wide seat belt type material is ideal but likely you will need to settle for a soft, marine grade rope instead.

Using nylon rope is almost worse then using nothing because of the abrasion factor.

  • The idea is to put a strap or rope between pairs of hoops every 12’ to 16’ and pull as tight as you can.
  • Use nails or eye bolts on your base as the spot for securing the ropes or straps.

If your cover is especially loose, it is best to install each of the ropes or straps snugly first. Then go back and tighten them as tight as you can. This will prevent you from pulling too much in one spot.

Please don’t hesitate to call if you have any questions about this technique. We would be happy to help clarify anything you need, to keep your building secure.

image

Retightening a Loose Structure Cover

Previously we outlined how to do a temporary fix for loose cover. This should not be left for an extended period. Re-tightening a cover does not have to be done in one day.

  • The job MUST split into two parts lengthwise.
  • The cover must be pulled lengthwise BEFORE it is pulled from side to side.
  • Make sure you do the tightening process on a calm, warm day.
  • You should do the end which looks the worst first.
  • This job will require taking ALL of the cover fasteners out.

Taking a short cut will leave you with more wrinkles.
Areas with wrinkles will flutter more and cause stress points.
This will also cause the cover to deteriorate quicker.

When you are tightening the cover, you should always pull 90 degrees to the wrinkle.

This means that after you have secured at the peak,
most often you will be pulling diagonally to the corner.

Once you have done one end/half and the wind is still down, you can start loosing the fasteners on the other end and repeat the process until complete.

Please don’t hesitate to contact us if you have any questions.

You can also see additional information in our installation guide:
Tarp Covering Instructions
Plastic Covering Instructions
Wirelock & Side Wall Cover Fasteners
covering options

Temporary Fix for a Loose Cover

There are a number of instances where a cover will need to be installed in less than ideal conditions. This can be either be on a windy day or in the cold (-10C or worse) and the job simply can not wait.

This will almost invariably lead to a situation where the cover will need to be re-tightened on a warmer and/or calmer day.

Doing this temporary fix will get you an extra month of time that you can wait until it warms up and you can do a better job retightening the loose cover.

The lifespan of a cover can very quickly be reduced if it is repeatedly flapping in the hard wind. A very effective, temporary fix to give you more time to do the job right, is to put ropes or straps over the building (as in the photos below)

A 1” or 2” wide seat belt type material is ideal but likely you will need to settle for a soft, marine grade rope instead.

Using nylon rope is almost worse then using nothing because of the abrasion factor.

  • The idea is to put a strap or rope between pairs of hoops every 12’ to 16’ and pull as tight as you can.
  • Use nails or eye bolts on your base as the spot for securing the ropes or straps.

If your cover is especially loose, it is best to install each of the ropes or straps snugly first. Then go back and tighten them as tight as you can. This will prevent you from pulling too much in one spot.

Please don’t hesitate to call if you have any questions about this technique. We would be happy to help clarify anything you need, to keep your building secure.

image

Retightening a Loose Structure Cover

Previously we outlined how to do a temporary fix for loose cover. This should not be left for an extended period. Re-tightening a cover does not have to be done in one day.

  • The job MUST split into two parts lengthwise.
  • The cover must be pulled lengthwise BEFORE it is pulled from side to side.
  • Make sure you do the tightening process on a calm, warm day.
  • You should do the end which looks the worst first.
  • This job will require taking ALL of the cover fasteners out.

Taking a short cut will leave you with more wrinkles.
Areas with wrinkles will flutter more and cause stress points.
This will also cause the cover to deteriorate quicker.

When you are tightening the cover, you should always pull 90 degrees to the wrinkle. This means that after you have secured at the peak, most often you will be pulling diagonally to the corner.

Once you have done one end/half and the wind is still down, you can start loosing the fasteners on the other end and repeat the process until complete.

Please don’t hesitate to contact us if you have any questions.

You can also see additional information in our installation guide:
Tarp Covering Instructions
Plastic Covering Instructions
Wirelock & Side Wall Cover Fasteners
covering options

Temporary Fix for a Loose Cover

There are a number of instances where a cover will need to be installed in less than ideal conditions. This can be either be on a windy day or in the cold (-10C or worse) and the job simply can not wait.

This will almost invariably lead to a situation where the cover will need to be re-tightened on a warmer and/or calmer day. Doing this temporary fix will get you an extra month of time that you can wait until it warms up and you can do a better job retightening the loose cover.

The lifespan of a cover can very quickly be reduced if it is repeatedly flapping in the hard wind. A very effective, temporary fix to give you more time to do the job right, is to put ropes or straps over the building (as in the photos below)

A 1” or 2” wide seat belt type material is ideal but likely you will need to settle for a soft, marine grade rope instead. Using nylon rope is almost worse then using nothing because of the abrasion factor.

The idea is to put a strap or rope between pairs of hoops every 12’ to 16’ and pull as tight as you can. Use nails or eye bolts on your base as the spot for securing the ropes or straps.

If your cover is especially loose, it is best to install each of the ropes or straps snugly first. Then go back and tighten them as tight as you can. This will prevent you from pulling too much in one spot.

Please don’t hesitate to call if you have any questions about this technique. We would be happy to help clarify anything you need, to keep your building secure.

image image(1)

**Originally Published May 5/15**