Tag Archives: ends

Covering Ends – Plastic & Tarp

Please refer to the Ends page in the assembly guide as well

When you are covering the ends of the structure, there are some similarities and some fundamental differences when you are covering with plastic or with tarp.

The aluminum wirelock channel must be installed on the top side of the hoop before you start the cover. The framing must also be in place before you are putting on the cover.

Your cover will be a rectangle and you must double check if the two ends were supplied as one piece or not.

  • You start at the base of one side and go continuously over the peak so that there is not an edge at the peak.
  • The cover gets fastened, temporarily, at the base first on either side of the door and then pull out to the corners.

If there is ANY wind, do into the wind side first.

  • Please remember that whenever you have wrinkles or folds, you will pull 90 degrees to the wrinkle.

Excess on the end covers will only get trimmed off after the roof cover is on as well.

If you are covering the end with plastic

  • you would go with the extra of your rectangle and fasten it temporarily to the back side of your framing.
  • At the very most, at this stage you will put part of a wire insert on either side of the peak.
  • When the cover is sitting smooth, you can put some strapping on the vertical framing to hole the cover in place.

If you are covering the ends with tarp

  • you will need to remove the wirelock channel first.

This may seem like double work, but the channel is now curved to the building with the required screw holes.

  • The end tarp cover is sandwiched between the hoop and the bottom of the wirelock channel.
  • When you pull the tarp over the peak, you will reinstall the wirelock channel from the top and work down.
  • If you do the left, right or bottom first will be determined by where the wrinkles are (if any).

Please don’t hesitate to call if you have any questions at all and please watch the videos on our YouTube channel for more information

So You Want to Buy a Greenhouse…Your Guide For Planning a Greenhouse Purchase

Norm just published a book that we wanted to let you know about.
“So You Want to Buy a Greenhouse: Your Guide to Planning a Greenhouse Purchase”

​It’s available on Amazon for purchase, or you can go through our facebook page

We appreciate your support!

We are quite excited and know it will be a valuable resource for many. We will also have limited copies available at our open house June 2, 2017 10am-3pm or you can email or call the office and we will ship you out a copy if you don’t want to purchase online.

Based largely on Norm’s Greenhouses 101 speech from the Guelph Organic Conference, with many extra tidbits and stories from Norm’s experience along the way over the last 45 years, it’s certainly a useful resource for anyone considering, or maintaining their structure of any application. Please contact us if you have any questions. We hope you’ll enjoy the book, and that we’ll see you at the open house in a few weeks!

“I should have known that I would get into this business when I was younger because the highlight of my birthday was always getting new pieces to my Mechano set. Now, I often describe these structures as big Mechano sets. It feels very fitting.”

Are you considering purchasing a greenhouse to start your own operation?
Are you unsure of all your options and what you should know?
Do you want to know what you’re getting into?

Using Norm Eygenraam’s 45 years experience in the industry, we have created this book for you to help! Through illustrations, tips, stories, photos and more, we help you understand all you need to consider. We do use Multi Shelter Solutions examples throughout, as that is what we have easiest access to, but this is by no means a sales book.

This guide is meant to inform you of your choices and show you key considerations in your planning journey. We have tried to make this book as informative as possible, no matter which direction you choose to go.

Enjoy, and happy planning!

Available on Amazon for purchase, or you can go through our facebook page
We appreciate your support! See you June 2nd at the open house!

Covering Ends – Plastic & Tarp

Please refer to the Ends page in the assembly guide as well

When you are covering the ends of the structure, there are some similarities and some fundamental differences when you are covering with plastic or with tarp.
The aluminum wirelock channel must be installed on the top side of the hoop before you start the cover. You start at the base of one side and go continuously over the peak so that there is not an edge at the peak. Your cover will be a rectangle and you must double check if the two ends were supplied as one piece or not. The framing must also be in place before you are putting on the cover.

The cover gets fastened, temporarily, at the base first on either side of the door and then pull out to the corners. If there is ANY wind, do into the wind side first. Please remember that whenever you have wrinkles or folds, you will pull 90 degrees to the wrinkle. Excess on the end covers will only get trimmed off after the roof cover is on as well.

If you are covering the end with plastic, you would go with the extra of your rectangle and fasten it temporarily to the back side of your framing. At the very most, at this stage you will put part of a wire insert on either side of the peak. When the cover is sitting smooth, you can put some strapping on the vertical framing to hole the cover in place.

If you are covering the ends with tarp, you will need to remove the wirelock channel first. This may seem like double work, but the channel is now curved to the building with the required screw holes. The end tarp cover is sandwiched between the hoop and the bottom of the wirelock channel. When you pull the tarp over the peak, you will reinstall the wirelock channel from the top and work down. If you do the left, right or bottom first will be determined by where the wrinkles are (if any).